|
FLEETLINE
PLATFORM |
|
Lengths: |
7', 8', 9'6"
8', 9'6", 12' 8', 9'6", 12', 14' |
| Widths: |
78"
87 1/4"
96" |
| Floor
Types: |
Standard
2x6 T&G, COP-8, #1 Structural Select SYP
10 ga Smooth Steel
12 ga Treadplate Steel
Optional Apitong Wood
3/16" Smooth Steel
3/16" Treadplate Steel
Steel Overlays |
| Side &
End Rails: |
5" face 12 gauge |
| Cross
Sills: |
3 1/4" face 12
gauge; 24" on center standard, 16" optional |
|
Longsills: |
4" 5.4# Structural
Channel |
| C/M
Gussets: |
9 1/4" x 5 1/2" - 10
gauge, at every cross sill |
|
Lighting: |
Required lighting
and marking per FMVSS108, installed |
| Wiring
Harness: |
Weather resistant,
SAE #J-1128 |
| Paint: |
Primed & painted
with Industrial Enamel |
Standard
finish on platforms is black w/decals. Other options or
modifications
available on request.
Note: Fleetline platforms not recommended for hoist
mounting. |
|
Specifications subject to change without notice |
top
|
TOUGHLINE
PLATFORM |
| Lengths: |
8', 9'6", 12'
8', 9'6", 10', 12', 14', 16', 18', 20', 22', 24 |
| Widths: |
87 1/4"
96" |
| Floor Types: |
Standard:
2x6 T&G, COP-8, #1 Structural Select SYP
10 gauge Smooth Steel
12 guage Treadplate Steel
Optional:
Apitong Wood
3/16" Smooth Steel
3/16" Treadplate Steel
Steel Overlay |
| Side & End Rails: |
6 3/4" face 11 gauge |
| Stake Pockets: |
Accommodates 2" x 4" nominal
lumber or our standard stakes |
| Cross Sills: |
4 7/8" face 11 gauge; 16" on
center standard,
12" optional |
| Longsills: |
8' - 12', 5" 6.7# structural
channel
14'-16', 6" 8.2# structural channel
18'-24', 7" 9.8# structural channel |
| C/M Gussets: |
9 1/4" x 5 1/2" - 10 gauge, at
every cross sill |
| Lighting |
Required lighting and marking per
FMVSS108, installed |
| Wiring Harness: |
Weather resistant, SAE #J-1128 |
| Paint: |
Primed & painted with Industrial
Enamel |
Standard finish on
platforms is black with decals. Other options or
modifications
available on request. |
| Specifications
subject to change without notice |
Top of Page
|
STRUCTURELINE PLATFORM |
| Lengths: |
12', 14', 16', 18', 20', 22',24' |
| Width: |
96" OD |
| Floor Types: |
Standard: 2x6T&G,
COP-8, #1
Structural Select SYP
10 gauge Smooth Steel
12 gauge Treadplate Steel
Options: Apitong
Wood
3/16" Smooth Steel
3/16" Treadplate Steel
Steel Overlays |
| Side & End Rails: |
6" - 8.2# Structural Channel |
| Outside Pockets: |
1 13/16" x 3 9/16" - 1/4" formed
steel with pocket spacers
(1/4" x 1/2"). Will accommodate 2x4 or our standard stake |
| Outside Tie Rail: |
3/8" x 2" flat bar |
| Cross Sills: |
4" - 5/4# Structural Channel; 12"
on center |
| Longsills: |
12'
5" - 6/7#
14' - 16' 6" - 8.2#
18' - 24' 7" - 9.8# |
| Gussets: |
9 1/4" x 5 1/2" at every cross
sill |
| Lighting: |
Required lighting and marking per
FMVSS108, installed |
| Wiring Harness: |
Weather resistant, SAE #J-1128 |
| Paint: |
Primed & painted with Industrial
Enamel |
|
Standard finish on platforms is
black with decals. Other options or modifications
available on request. |
|
Specifications subject to change without notice |
Top of Page
|
RANCHER PLATFORM |
|
Sizes: |
8'3" x 84" - 92" - 96", 9' x 92" -
96" - 991/2", 10', 11', 12' x 96" or 99 1/2",
96" & 99 1/2" wide bodies are tapered at front for sleek style
and appearance. Square front optional. |
|
Floor: |
Treadplate, 12 gauge |
|
Side Rail: |
7" vertical face |
|
Pockets: |
3/16" formed steel to accommodate 2" x 4" lumber |
|
Tie Rail: |
3/8" x 2" steel segmented for ease in fuel fill
installation |
|
Crossmembers: |
3" - 4.1# structural channel |
|
Longsills: |
5" - 6.7# structural channel |
|
Headboard: |
14 gauge smooth steel panel with 3" x 2" – 11
gauge rectangular tubing frame with
louvered window;
39" high; 35" high on 8'3" x 84" |
|
Rear Apron: |
3/16" smooth steel |
|
Gooseneck Hitch: |
Recessed gooseneck hitch with safety chain loop
standard, (ball not included) Atwood B-25 retractable ball
assembly optional |
|
Receiver Hitch: |
3" x 4" x ¼" rectangular tubing frame with tube
for 2" receiver hitch; safety chain loops;
and tail light brackets |
|
Lights: |
Required
lighting & marking per FMVSS108 installed |
| Standard
finish for platforms is black. |
|
Specifications subject to change without notice |
Top of Page
|
CONTRACTOR RACKS DROP DOWN |
| Lengths: |
8', 10', 12', 14', 16', and 18' |
| Width: |
96" OD 90" ID |
| Bulkhead: |
* 42" high 12 ga. formed steel
panel
* 24" high x full width screened window
* 14 ga. formed steel stakes with liners
* Knee brace gusset kit |
| Sides |
* 14" high 12 ga. formed steel
panel
* 14 ga. formed steel stakes
Spring loaded latches at each end
Forged butt hinge & pin with 1/4" thick strap hinge |
| Tail Gate: |
* 14" high 12 ga. formed steel
panel
* 12 ga. formed steel vertical stiffeners
2 1/2" x 2 1/2" x 12 ga. tube horizontal stiffener
* Forged butt hinge & pin with 1/4" thick strap hinge
3/16" rear rail cap
Spreader chains |
| Corner Posts: |
14" high 12 ga. formed steel
10 ga. corner cap with spring loaded latch pin/hinge
Inside stakes 14 ga. formed steel with liners
Tapered inside for easier material flow |
| Hardware |
* All attaching hardware
included |
|
LIFT OUT STYLE |
| Lengths: |
8', 9'6", 10', 12', 14', 16', 18'
and 20' |
| Widths: |
96" OD 90" ID & 87
1/4" OD 81 1/4" ID |
| |
Specifications marked with * from
above apply |
|
Specifications subject to change without notice |
Top of Page
|
GRAIN RACKS |
| Heights: |
42", 52" |
| Interior Length: |
6" less than platform |
| Interior Width: |
87 1/4" = 81 3/4"
96" = 90 1/2" |
| Panel Skins: |
42", 16 gauge rollformed
52", 14 gauge rollformed |
| Stakes: |
14 gauge with liners |
| Rears: |
42" - 2 wings, 39 5/8" x 32" high
grain gate, 10" filler panel, bull bar
52" - same but with 20" filler panel |
|
TIP TOP |
| Heights: |
10" |
| Interior Length: |
6" less than platform |
| Interior Width: |
87 1/4" = 81 3/4"
96" = 90 1/2" |
| Panel Skin: |
16 guage rollformed |
| Stakes: |
14 gauge |
| Rears: |
1 piece, full width |
| Specifications
subject to change without notice |
Top of Page
|
STAKE RACKS |
| Lengths: |
7', 8', 9'6", 10', 12', 14', 16',
18', 20', 22', 24' |
| Standard Heights: |
7', 8', 9'6", 12'- 30"
9'6" , 10', 12', 14', 16', 18', 20', 22', 24 - 40"
Other Heights on request |
| Interior Dimensions: |
6" less than length and width |
| Slats: |
6" 16 gauge rollformed steel or 1
x 6 pine |
| Stakes: |
15 gauge rollformed with liners |
| Front: |
12 gauge bulkhead w/full width
window standard
Stake front optional |
| Rears: |
Hinged, swing out |
| Hardware: |
Western style heavy duty spring
loaded gate locks with plated
hinge rods on swing gate and rears. |
| Hold down latch: |
Spring-loaded in stake: 1 per
section |
| Side Sections: |
7'-10'
2-piece sides
12'-20' 3-piece sides/1 swing gate per side
22'-24' 4-piece sides/1 swing gate per side |
| Finish |
Powder Coat Gloss Black |
|
Specifications Subject to Change without notice |
Top of Page
|
LANDSCAPE RACKS |
| Lengths: |
8 ft. thru 24 ft. |
| Width: |
9'6" |
| Heights: |
42" and 52" |
| Interior Dimensions: |
6" Less than length
and width |
| Sides
and Front: |
42" = 16
Ga. 52" = 14 Ga.
Roll formed with integral tarp rail for strength
and rigidity. Stakes are 14 Ga. with 12 Ga.
liner/reinforcement. Anti-spread chains and knee brace
gusset included. |
| Side
Door: |
14 Ga.
door panel with 2" x 14 Ga. square tubing frame, heavy-duty
hinges, doorstops, handle, and spring loaded door latch.
Opening is 47 1/2 x full height. |
| Rear
Door: |
Double
opening doors with 14 Ga. door panel, 2" x 14 Ga. square tubing
frame, heavy duty hinges, spring loaded door latches, and hold
back chains. Opening is 89" x full height. Weld on
corner posts are 3" x 11 Ga. square tubing with 3/16"
platform corner reinforcement. |
| Optional
Rear: |
14" high
three-way contractor tailgate with heavy-duty hardware and
spreader chains. Double rear gate, 14 Ga. tubing frame,
heavy-duty hinges, spring loaded door latch, and hold back
chains. Weld on corner posts are 3" x 11 Ga. square tubing
with 3/16" platform corner reinforcement. |
| Optional
Cab Shield: |
formed
12 Ga. material, bolt or weld on.
1/4 = 12" 1/3 = 18"
1/2=24" |
|
Specifications subject to change without notice |
|
